Category: Aerospace
FLUID FILM
STOPTS
RUST
IMMEDIATELY
FLUID FILM AS-R
Fluid Film | Automobile | Home & Garden | Industry | Agriculture | Truck | Aerospace | Maritime shipping | Recreational boating | Wind turbines | Winter Service
VISCOSITY: low (e.g. like sirup)
CREEPABILITY: + + + +
DURRATION: ca. 4 years (in closed cavities)
PROCESSING: Spray can with additional Feinapplikator
FLUID FILM AS-R is a physiologically harmless, solvent-free and thixotropic single-layer corrosion protection coating with sliding and rust dissolving effect based on lanolin. It forms a clear and shiny protective film.
The 400 ml spray can contains FLUID FILM NAS with propane butane as propellant.
400 ml spray can as a universal product for commercial and private use for care, preservation, rust removal and as a lubricant.
FIELDS OF APPLICATION
FLUID FILM AS-R is very suitable for companies, workshops, garages and do-it-yourselfer for use as a preservative, maintenance, rust remover and lubricant.
On the car, it provides protection for folds, door edges, cavities, engine compartment as well as for all other corrosion-prone parts. Especially during decommissioning in winter, a thin film of FLUID FILM AS-R protects motorcycles, bicycles or boat parts against rust. Even on chains, joints, steel and metal surfaces, such as in machines and tools, FLUID FILM stops corrosion immediately or prevents it from developing in the first place. Manufacturing companies can also take advantage of this during transport and processing.
By combining corrosion inhibitors and lubricants, moving parts such as deflection rollers, chain transmissions or joints can be protected.
FLUID FILM AS-R is very effective for the maintenance of sports, leisure and household appliances or in the restoration sector, where special attention is paid to the original patina.
ADVANTAGES
In contrast to conventional products, FLUID FILM AS-R is more environmentally friendly and economical to use due to its solvent-free composition.
The basic substance lanolin is non-volatile like oil or kerosene and does not resinify. On the other hand, the effect of solvents usually subsides after 12-15 seconds, that of oil or kerosene ends after a few days, whereby then these conventional agents completely lose the protective effect.
Application
The use of the 400 ml spray can allow a uniform application to large areas with the normal spray attachment.
A 15 cm long spray tube is available on the can for precise use, even in difficult-to-reach places. For use in longer cavities, an approx. 60 cm long spray head extension with a 3-jet all-round nozzle can be supplied.
EFFECT
- is extremely resistant to all weather influences, including snow and slush and the dissolving salts used in winter service.
- extremely effective and reliable at the same time as a rust remover and water displacing corrosion inhibitor
- excellent salt water resistance
- fast creeping, yet well adhering
- temperature stable
- is not washed off or altered by rain and seawater
- does not evaporate or resinifies, as is it usual by most of penetrating oil
- plastifies and activates already existing bitumen protective layer on the underbody of vehicles
FLUID FILM AS-R spray cans comply with MIL-Spec C-23050 guidelines.
Packaging
- FLUID FILM AS-R is available as a 400 ml spray can with extra spray tube
- Packaging unit: 12 cans in carton
- A 60 cm long spray head extension with 3-jet all-round nozzle is available as an accessory
TECHNICAL DATA SHEET (PDF)
For a full screen view, click on the diagonal cross.
To download the PDF, click on the 3 dots on the left and then go to “Download”.
Dieses Video wird von YouTube bereitgestellt. Mit dem Abspielen dieses Videos akzeptieren Sie die YouTube Datenschutzbestimmungen.
FLUID FILM in use at Mercedes
Dieses Video wird von YouTube bereitgestellt. Mit dem Abspielen dieses Videos akzeptieren Sie die YouTube Datenschutzbestimmungen.
FLUID FILM application example – Detlef Wulff Hodt
Dieses Video wird von YouTube bereitgestellt. Mit dem Abspielen dieses Videos akzeptieren Sie die YouTube Datenschutzbestimmungen.
FLUID FILM application example – Manfred Rusch “Goldie” VW Beatle Club
FLUID FILM
STOPTS
RUST
IMMEDIATELY
FLUID FILM NAS
Fluid Film | Automobile | Industry | Agriculture | Truck| Maritime shipping | Wind turbines | Winter Service
VISCOSITY: low-medium (eg. like ketchup)
CREEPABILITY: + + +
DURATION: ca. 8 years (in closed cavities)
PROCESSING: with conventional compressed air systems to heat the material to about 25 ° C or with airless systems
FLUID FILM NAS is a physiologically harmless, solvent-free and thixotrophic single-layer corrosion protection coating with sliding and rust-dissolving effect based on lanolin. It forms a clear and shiny protective film.
APPLICATIONS
FLUID FILM NAS is mainly applied as rust protection of metal surfaces during internal interim storage, for preservation during sea and road transport and for cavity sealing of motor vehicles. It can also be used as a lubricant and creeping agent as well as in winter service.
In conventional processing by means of sprayers, brushes or rollers for corrosion protection measures on dry or damp, bare or rusty surfaces, which are to be protected against salt water and weather influences. For cavities on motor vehicles, FLUID FILM NAS can be used by means of a pressure cup gun with a cavity probe (0.2 or 0.4 mm) after heating to approx. 25°C.
THICKNESS
The effectiveness of a rust protection system depends, among other things, on its layer thickness. It has to be selected according to the given stress and the service life of the object.
We recommend double the layer thickness when protecting cavities with many corners, rebates and overlaps and the presence of an old coating or flash rust.
Surface Preparation
FLUID FILM NAS can be used as a rust remover and at the same time as a corrosion inhibitor. For economic reasons, it is recommended to remove loose dirt such as rust and old coating parts by washing them out. The surface may be moist, but must be cleaned of surface water.
EFFECT
- solvent-free and physiologically harmless during application and as a protective film;
- requires minimal surface treatment, penetrates rust, displaces water and forms a highly resistant protection against corrosion by salts
- good adhesion to damp or dry surfaces
- no evaporation, resinification or drying out of the protective film
- can be easily removed if necessary
- may come into contact with water immediately after application
Packaging
- 1 litre plastic bottle
- 1 litre cartridge
- 5 litre plastic canister
- 20 litre pail
- 208 litre drum
BROCHuRE (PDF)
For a full screen view, click on the diagonal cross.
To download the PDF, click on the 3 dots on the left and then go to “Download”.
FLUID FILM
StoptS
RUst
Immediatly
FLUID FILM WRO-EP
Fluid Film | Industry | Agriculture | Truck | Aerospace | Shipping | Recreational boating | Wind turbines | Winter service
VISCOSITY: very high (e.g. ike hard butter)
CREEP ABILITY: +
PROTECTION PERIOD: approx. 30 Years (in closed cavities)
PROCESSING: Wire rope lubricator or brush / roller / wool glove
MILITARY APPROVAL: MIL-G-18458B (SH)
FLUID FILM WRO-EP – The solvent-free preservative produced on a wool grease basis offers high-quality corrosion protection for all conditions. It contains anti-aging agents, antioxidants, inhibitors, wetting agents and additives to increase lubricating compressive strength.
It is suitable as a permanently active corrosion protection for wire ropes and screw connections under extreme loads.
FLUID FILM WRO-EP can be used at temperatures from – 45°C up to + 96°C, under extreme pressure conditions. Due to the very high viscosity, this product can only be used to a limited extent as a top coat, but as a strong film-forming material, it is ideally suited as a top coat for sealing and enveloping the rope spandrels and individual wires.
Liquid A can be used for deep penetration.
Surface Preparation
In the case of new wire ropes, the surface should be largely freed from the stranding agent before FLUID FILM WRO-EP is applied. The stranding agent need not be removed from the spandrels between the individual wires.
If well-adhering old coatings are to be retained on used ropes, they must be examined for their functionality; these include, in particular, the adhesion as well as the degree of underrusting and infiltration by water. Before applying the top coat, foreign layers (impurities) must be removed. Damaged areas must be mechanically derusted, at least to the standard purity grade St 1 according to SIS (loose rust), and applied with a base coat. Poorly adhering parts of old coatings should be removed by brushing or with the help of the MASTO wire rope lubrication device.
Application
Apply with hard brushes, rags, sheep’s wool gloves or leather cones.
For long-term protection, a target layer thickness of the top coat of at least 800 μm is required. However, the material can be applied up to 3 mm, whereby it still has a high mechanical strength and a high adhesion. The most effective way is to inject FLUID FILM WRO-EP with the MASTO wire rope lubrication device.
Effect
- Solvent-free, therefore less environmental impact during handling
- Very high resistance and durability against saltwater and chemicals
- Temperature-stable from -45°C up to 110°C
- High mechanical strength, superior adhesiveness under extreme climatic conditions
- Excellent wear protection respectively EP compounds
- Economical in application and uncomplicated in handling. In one step a coating of up to 3.000 µm can be applied.
- 1-component product with 98 % solids content
Packaging
- cartridge 310 ml
- 17.6 litre pail
- 208 litre drum
Dieses Video wird von YouTube bereitgestellt. Mit dem Abspielen dieses Videos akzeptieren Sie die YouTube Datenschutzbestimmungen.
FLUID FILM in action at Mercedes